Estimation of genetic parameters for dry rubber yield, girth, bark thickness and number of latex vessels ring in a synthetic population of rubber clone
Abstract:
ประชากรยางพาราพันธุ์สังเคราะห์ 341 ต้น เกิดจากการผสมพันธุ์แบบเปิดระหว่างยางพารา 5 พันธุ์ ปลูกในแปลงจำนวน 8 แปลง (บล็อก) แปลงละ 8 ต้น ด้วยระยะห่างระหว่างต้น 4 × 4 เมตร ข้อมูลผลผลิตน้ำยาง เส้นรอบลำต้น ความหนาเปลือก และจำนวนวงท่อน้ำยาง ถูกนำมาใช้ในการประมาณค่าพารามิเตอร์ทางพันธุกรรม หุ่นจำลองทางพันธุกรรมเชิงเส้นตรงแบบผสมสำหรับลักษณะที่เกิดซ้ำ (Repeatability Mixed Linear Model) และพิจารณาปี-เดือนที่วัดค่า กลุ่มพันธุ์ และแปลงปลูก (บล็อก) เป็นปัจจัยกำหนด โดยมีความสามารถทางพันธุกรรมแบบบวกสะสมของต้นยางแต่ละต้น อิทธิพลจากสภาพแวดล้อมถาวร และความคลาดเคลื่อนสุ่มเป็นปัจจัยสุ่ม องค์ประกอบของความแปรปรวนสำหรับแต่ละลักษณะถูกประมาณค่าด้วยวิธี Average Information - Restricted Maximum Likelihood แล้วนำไปคำนวณค่าพารามิเตอร์ทางพันธุกรรม ความสามารถทางพันธุกรรมแบบบวกสะสมของต้นยางแต่ละต้น (Estimated Breeding Value; EBV) ถูกทำนายด้วยวิธี Best Linear Unbiased Prediction (BLUP) ผลการศึกษาพบว่า อัตราพันธุกรรม (0.91±0.01 ถึง 0.93±0.01) และอัตราซ้ำ (0.97±0.003 ถึง 0.98±0.002) สำหรับเส้นรอบลำต้นมีค่าสูง และมีสหสัมพันธ์ระหว่างลักษณะเส้นรอบลำต้นและผลผลิตน้ำยางสูงในทางบวก (0.72; P < 0.05) อัตราพันธุกรรม (0.61±0.03) และอัตราซ้ำ (0.63±0.03) ของผลผลิตน้ำยางมีค่าสูง ในขณะที่อัตราพันธุกรรมและอัตราซ้ำสำหรับความหนาเปลือกมีค่าเท่ากับ 0.35±0.03 และ 0.70±0.06 ใกล้เคียงกับอัตราพันธุกรรมและค่าอัตราซ้ำสำหรับจำนวนวงท่อน้ำยางมีค่าเท่ากับ 0.36±0.03 และ0.72±0.06 ตามลำดับ นอกจากนี้ ยางพาราในกลุ่ม PB 260 × IAN 873 มีค่า EBV สำหรับผลผลิตน้ำยาง (+35.41±3.97 กรัม) และเส้นรอบลำต้นที่ระดับความสูงจากพื้นดิน 150 เซนติเมตร (+8.51±1.07 เซนติเมตร) มีค่าสูงที่สุด ผลการศึกษา ชี้ให้เห็นถึง โอกาสในการพัฒนาศักยภาพทางพันธุกรรมสำหรับลักษณะที่ศึกษาในประชากรยางพาราพันธุ์สังเคราะห์ด้วยวิธีการคัดเลือกความสามารถทางพันธุกรรม
A synthetic population of 341 rubber tree derived from cross-pollination five female parent trees, the clones were planted with eight replications (block) and eight plants per plot with 4 × 4 meters spacing. The data of dry rubber yield, girth, bark thickness and number of latex vessel ring were used to estimate genetic parameters. A repeatability mixed linear model that considered year-month measured, breed group, replications (block) as fixed effects, and random effects were additive genetic effect, permanent environment effect and the residual. Variance components estimations for study traits were estimated by an Average Information-Restricted Maximum Likelihood procedure was used to estimate genetic parameters. The estimated breeding value of each rubber tree were estimated by Best Linear Unbiased Prediction. The results from this study show that heritability (0.91±0.01 to 0.93±0.01) and repeatability (0.97±0.003 to 0.98±0.002) for girth was high and positive genetic correlation between girth and dry rubber yield (0.72; P < 0.05). The heritability (0.61±0.03) and repeatability (0.63±0.03) for dry rubber yield was high, while heritability and repeatability for bark thickness was 0.35±0.03 and 0.70±0.06 similar to heritability and repeatability for number of latex vessels ring was 0.36±0.03 and 0.72±0.06 respectively. In addition, open-pollinated progenies of PB 260 × IAN 873 population had EBV for dry rubber yield (+35.41±3.97 gram) and girth at 150 cm above the ground (+8.51±1.07 centimeter) were highest. These results indicated that the opportunity of genetic improvement for all traits in this study in a synthetic population of rubber clone with selection based on estimated breeding value