แจ้งเอกสารไม่ครบถ้วน, ไม่ตรงกับชื่อเรื่อง หรือมีข้อผิดพลาดเกี่ยวกับเอกสาร ติดต่อที่นี่ ==>
หากไม่มีอีเมลผู้รับให้กรอก thailis-noc@uni.net.th
หากไม่มีอีเมลผู้รับให้กรอก thailis-noc@uni.net.th
Kamonpong Jamkamon. Influence of processes parameter on the machinability of wire electrical discharge machining for tool steel grade JIS SKD 11. (). King Mongkut's University of Technology North Bangkok. Central Library. : , 2024.
Influence of processes parameter on the machinability of wire electrical discharge machining for tool steel grade JIS SKD 11
Name: Piyapong Kumkoon
Organization :
Rajamangala University of Technology Krungthep. Faculty of Engineering
Email :
piyapong.k@mail.rmutk.ac.th
Name: Suppawat Chuvaree
Organization :
Rajamangala University of Technology Krungthep. Faculty of Engineering
Email :
suppawat.c@mail.rmutk.ac.th
Name: Pichai Janmanee
Organization :
Rajamangala University of Technology Krungthep. Faculty of Engineering
Email :
pichai.j@mail.rmutk.ac.th
Name: Kamonpong Jamkamon
Organization :
Rajamangala University of Technology Krungthep. Faculty of Engineering
Email :
kamonpong.j@mail.rmutk.ac.th
LCSH:
Electric metal-cutting
LCSH:
Machinability
LCSH:
Tool steel
LCSH:
Manufacturing processes
Abstract:
Wire electrical discharge machining is a modern
manufacturing process that is widely used on difficult-to-cut
materials with a controlled discharge current in order to erode
a conductive workpiece. An adjustment of the controlled
parameters can possibly effect the machinability of the
machining process. Therefore, this study aims to investigate the
influence of controlled parameters on the machinability of wire
electrical discharge machining for cutting JIS SKD11 grade tool
steel. The controlled parameters consist of feed rate and pulse
duty factor. The machinability was evaluated in terms of cutting
speed and kerf width. In addition the quality of the machined
surface was evaluated by arithmetic average roughness. The
results showed that cutting speed directly increased with the
feed rate for the workpiece at a thickness of 10 mm. However,
an approximately 63.50% reduction in the cutting speed was
found at the highest feed rate of 5 mm/min and 27.0% for the
workpiece thickness at 50 and 25 mm, respectively. The kerf
width and surface roughness slightly decreased with the feed
rate. The lowest roughness levels were shown at approximately
2.48, 2.40 and 2.46 μm and for the feed rates of 3, 4 and 5
mm/min for the workpiece thickness of 10, 25 and 50 mm,
respectively. In addition, the cutting speed, kerf width and
roughness of the machined surface increased with the pulse duty
factor due to greater duration of pulse on time in the discharge
cycle.
King Mongkut's University of Technology North Bangkok. Central Library
Address:
BANGKOK
Email:
library@kmutnb.ac.th
Created:
2024
Modified:
2025-02-07
Issued:
2025-02-07
บทความ/Article
application/pdf
BibliograpyCitation :
In Rajamangala University of Technology Krungthep. 12th International Electrical Engineering Congress (iEECON 2024) (pp.790-794). Bangkok : Rajamangala University of Technology Krungthep
eng
©copyrights King Mongkut's University of Technology North Bangkok
RightsAccess:
ใช้เวลา
0.028925 วินาที
Piyapong Kumkoon
| Title | Contributor | Type |
|---|---|---|
| Influence of processes parameter on the machinability of wire electrical discharge machining for tool steel grade JIS SKD 11
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าพระนครเหนือ Piyapong Kumkoon;Suppawat Chuvaree;Pichai Janmanee;Kamonpong Jamkamon | บทความ/Article | |
| Electrical discharge machining process on tungsten carbide using copper titanium-nitride electrode materials
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าพระนครเหนือ Pichai Janmanee;Piyapong Kumkoon;Paiboon Yaemphuan;Rattikorn Saodaen;Chutharat Sarod;Kritsana Uamnuson | บทความ/Article |
Suppawat Chuvaree
| Title | Contributor | Type |
|---|---|---|
| Influence of processes parameter on the machinability of wire electrical discharge machining for tool steel grade JIS SKD 11
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าพระนครเหนือ Piyapong Kumkoon;Suppawat Chuvaree;Pichai Janmanee;Kamonpong Jamkamon | บทความ/Article |
Pichai Janmanee
| Title | Contributor | Type |
|---|---|---|
| Surface roughness of electrical terminal blocks in the plastic injection process
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าพระนครเหนือ Pichai Janmanee;Kritsana Uamnuson;Rattikorn Saodan;Paiboon Harnmont;Ekachai Rodpisa;Jedsadapong Nimvongsa | บทความ/Article | |
| Influence of processes parameter on the machinability of wire electrical discharge machining for tool steel grade JIS SKD 11
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าพระนครเหนือ Piyapong Kumkoon;Suppawat Chuvaree;Pichai Janmanee;Kamonpong Jamkamon | บทความ/Article | |
| Sintering of Cu-TiCN electrode materials for electrical discharge machining process
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าพระนครเหนือ Pichai Janmanee;Paiboon Yaemphuan;Ekachai Rodpisa;Rattikorn Saodaen;Chutharat Sarod;Kritsana Uamnuson | บทความ/Article | |
| Electrical discharge machining process on tungsten carbide using copper titanium-nitride electrode materials
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าพระนครเหนือ Pichai Janmanee;Piyapong Kumkoon;Paiboon Yaemphuan;Rattikorn Saodaen;Chutharat Sarod;Kritsana Uamnuson | บทความ/Article |
Kamonpong Jamkamon
| Title | Contributor | Type |
|---|---|---|
| Influence of processes parameter on the machinability of wire electrical discharge machining for tool steel grade JIS SKD 11
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าพระนครเหนือ Piyapong Kumkoon;Suppawat Chuvaree;Pichai Janmanee;Kamonpong Jamkamon | บทความ/Article |