Abstract:
งานวิจัยนี้เป็นงานวิจัยที่เกี่ยวกับการพัฒนาเครื่องมือตรวจวัดทางธรณีเทคนิคชนิด Wire Extensometer โดยเครื่องมือที่พัฒนานี้สามารถตรวจวัดการเคลื่อนตัวของระนาบพิบัติซึ่งอยู่ระดับลึกใต้ชั้นดินได้อย่างต่อเนื่องและสามารถวัดปริมาณการเคลื่อนตัวได้มากกว่า 800 มิลลิเมตร ซึ่งมีการสอบเทียบความถูกต้องในห้องปฏิบัติการตามมาตรฐาน JIS B7516: 1987 และใช้วัสดุที่ราคาประหยัดหาง่ายภายในประเทศอีกทั้งมีความทนต่อสภาพแวดล้อมในสนาม เครื่องมือ Wire Extensometer มีการทำงานคือ นำลวดสเตนเลสปลายหนึ่งยึดติดกับชั้นหินที่ไม่เคลื่อนตัวก้นหลุม เจาะ ส่วนปลายอีกด้านหนึ่ง ยึดติดกับชุดเครื่องมือ Wire Extensometer ซึ่งติดตั้งบนแท่นเหนือหลุมเจาะบนผิวเชิงลาด เมื่อเชิงลาดมีการเคลื่อนตัวเส้นลวดจะเคลื่อนตัวชุดเพลาและเฟืองซึ่งเชื่อมต่อกับมู่เล่และขับมาตรวัด (Meter) ซึ่งแสดงปริมาณการเคลื่อนตัวของเส้นลวด นอกจากนี้ชุดเพลายังเชื่อมต่อกับอุปกรณ์ Potentiometer ซึ่งจะให้สัญญาณไฟฟ้าที่สัมพันธ์กับองศาและรอบการหมุนของชุดเพลา เพื่อส่งข้อมูลการเคลื่อนตัวของเส้นลวดผ่านชุดอุปกรณ์ส่งสัญญาณไร้สายระยะไกลมายังวิศวกรเพื่อนำข้อมูลใช้ในการประมวลผลต่อการเคลื่อนตัวของระนาบพิบัติ ในการวิจัยนี้ได้ดำเนินการติดตั้งเครื่องมือ Wire Extensometer เพื่อตรวจวัดการเคลื่อนตัวของเชิงลาดของมวลหิน (Rock Mass Slab) บริเวณพื้นที่ 4.1 ของเหมืองแม่เมาะ จังหวัดลำปาง จากการติดตั้งเครื่องมือ Wire Extensometer สามารถวัดการเคลื่อนตัวของเชิงลาดได้อย่างต่อเนื่องเป็นระยะเวลาประมาณ 3 ปี และให้ผลการตรวจวัดที่แม่นยำใกล้เคียงกับเครื่องมือตรวจวัด Georobot ที่ติดตั้งบริเวณเดียวกันจากการแปรผลการวัดจากเครื่องมือ Wire Extensometer พบว่ามวลหิน บริเวณพื้นที่ 4.1 มีการเคลื่อนตัวอย่างต่อเนื่องตามแนวระนาบพิบัติไปแล้ว 596.7 มิลลิเมตร (ณ วันที่ 22 มิถุนายน 2558) และเมื่อนำผลการเคลื่อนตัวของมวลหินหาความสัมพันธ์กับช่วงเวลา พบว่ามวลหินมีอัตราการเคลื่อนตัวเฉลี่ย 181.7 มิลลิเมตรต่อปี และจากความสัมพันธ์การเคลื่อนตัว ของมวลหินกับช่วงเวลาสามารถพิจารณาแนวโน้มการเคลื่อนตัวของมวลหินบริเวณพื้นที่ 4.1 เพื่อ ประเมินการเคลื่อนตัวของมวลหินระหว่างการดำเนินงานขุดให้มีความปลอดภัย
This research is emphasis on a development of wire extensometer for large slope movement monitoring. The wire extensometer could continually measure deep slip surface movement of 800 mm. The instrument had been calibrated in laboratory according to JIS B7516: 1987 standard. All of the instrument parts were made products which is low cost and durable. The principle of the wire extensometer is to attach an end of stainlesssteel wire at the bottom of borehole under the slip plane, while the other and is connected to the wire extensometer which was installed on a slope surface. As the slope moves, the wire, connected to a pull pulley system, is changed and forces meter rotation. The meter number informs the amount of wire movement. In addition, the pulley system is also connected to a potentionmeter which converts the movement data to digital format. When the instrument is connected to a remote sensing instrument, it can sand the slope movement data for a long distance to a geotechnical engineer for slope stability analysis. After instrument calibration, the wire extensometer was installed on a potential failure slope area 4.1, Mae Moh Mine, Lampang province. The instrument could measure the slope movement continuously and the observed data was close to, the movement data obtained from georobot. The data analysis showed that the observed slope had continuously moved to 596.7 mm. (measured on June 22, 2015). The amount of movement and with the rate of 181.7 mm./year, the rate of movement could be used for slope stability analysis and slope safety evaluation.